Safety instructions
Description of instructions
In this documentation the following instructions are used.
These instructions must be read carefully and followed without fail!
 DANGER
|
Serious risk of injury! Failure to follow this safety instruction directly endangers the life and health of persons. |
WARNING |
Risk of injury! Failure to follow this safety instruction endangers the life and health of persons. |
CAUTION |
Personal injuries! Failure to follow this safety instruction can lead to injuries to persons. |
Notice |
Damage to environment/equipment or data loss Failure to follow this instruction can lead to environmental damage, equipment damage or data loss. |
 | Tip or pointer This symbol indicates information that contributes to better understanding. |
Intended use
This device is designed for installation in a housing and is intended for general professional use, for example in industrial control systems or office, communication and measuring equipment.
Do not use this power supply in installations where a malfunction could cause serious injury or danger to human life.
Exclusion of liability
All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.
Personnel qualification
This description is only intended for trained specialists in control, automation and drive engineering who are familiar with the applicable national standards.
Safety regulations
Please note the following safety instructions and explanations!
Product-specific safety instructions can be found on following pages or in the areas mounting, wiring, commissioning etc.
Safety instructions and installation requirements for PS2001-2410-0000 power supply unit
DANGER |
Danger of electric shock, fire, injuries, injuries resulting in death! - Do not use the power supply without proper earthing (protective conductor). Use the terminal at the input terminal strip for the earth connection, not one of the screws on the housing.
- Switch off the power supply before working on the device. Provide protection against unintentional reconnection.
- Ensure proper wiring by following all local and national regulations.
- Do not modify or attempt to repair the device.
- Do not open the device, as high voltages are present inside.
- Avoid foreign bodies entering the housing.
- Do not use the device in damp locations or in areas where moisture or condensation is likely to occur.
- Do not touch the device when it is switched on or immediately after it has been switched off. Hot surfaces can cause burns.
|
WARNING |
Explosion hazard warning! Use only in standard vertical mounting orientation with the input terminals at the bottom of the device.
Replacement of components may affect the suitability for this environment.
Do not disconnect the device from the mains and do not operate the voltage adjustment unless the power is switched off or the environment can be considered safe.
For the end product a suitable housing must be provided, which has a minimum protection class of IP54 and meets the requirements of EN 60079-0. |
Notice |
Instructions for use in potentially explosive atmospheres The device is suitable for use in the following areas:
Class I Division 2 Groups A, B, C, D
and for use in Group II environments of Category 3 (Zone 2).
Classification:
ATEX: EPS 15 ATEX 1 101 X, II 3G EX ec nC IIC T4 Gc / IECEx EPS 20.0046X. |
| Further notes on installation requirements - This device contains no parts that require maintenance. If an internal fuse trips, this is due to an internal defect.
- If any damage or malfunction occurs during installation or operation, turn off the power immediately and return the device to the factory for inspection.
- Mount the device on a DIN rail so that the input terminals are at the bottom of the device. For other mounting positions, please refer to the load reduction requirements in this document. See chapter Installation positions.
- This device is designed for convection cooling and does not require an external fan. Do not obstruct the air circulation. No more than 15% of the ventilation grille may be covered (e.g. by cable ducts)!
- Maintain the following installation distances: 40 mm at the top, 20 mm at the bottom and 5 mm on the left and right are recommended if the device continuously runs at more than 50% of the rated output. Increase this distance to 15 mm if the adjacent device is a heat source (e.g. another power supply unit).
|